How to Make Clap Switch | DIY Project | Using 555 Timer IC | Homemade | Electronics Projects

How to Make Clap Switch | DIY Project | Using 555 Timer IC | Homemade | Electronics Projects

Hello , Today In This Tutorial I Am Going To Show You Step By Step ( Home Made )

How to make Clap Switch Using 555 Timer IC Simple Electronic Project Home Easy DIY

This Electronic Project is Very Simple Easy and DIY (Do It Yourself)

Please Subscribe ↪

You Will Find Full Project Description and All Useful Material Including

• Circuit Diagram / Schematic
• Hardware / Component List
• Code
• Datasheet
• Pin Configuration Etc

At ↪
At ↪

Thanks for Watching It.
↪ For Any Difficulty Please Comment Below

Subscribe To Our Channel


Like Our Facebook Page


Required Components

Condenser Mic

555 Timer IC

Transistor BC547

Resistors (220, 1k, 47k, 100k ohm)

Capacitor (10uF)

LED and Battery (5-9v)

Project Description

Clap switch is an interesting hobby circuit which turns on the lights with a clap sound. Although its name is “Clap switch”, but it can be turned ON by any sound of approximately same pitch of Clap sound. The main component of this clap switch circuit is the Electric Condenser Mic, which has been used as a sound sensor. Condenser Mic basically converts sound energy into electrical energy, that in turns used to trigger 555 timer IC, through a Transistor. And triggering of 555 IC would turn ON the LED, which will be automatically turned OFF after some time. I have made this circuit as simple as possible, you can find many complex Clap switches (using 555 IC) with some more components in it, and merely doing the same thing. Even make things simpler require more effort than making it complex.

Here we are using Electric Condenser Mic for sensing the sound, transistor to trigger the 555 timer IC and 555 IC to turn ON the LED through a low voltage trigger.
You can see the circuits and connections in the above schematic diagram of clap switch. Initially the transistor is in OFF state because there is not enough (0.7v) base-emitter voltage to turn it ON. And the point A is at high potential, and point A is connected to Trigger pin 2 of 555 IC, as a result Trigger pin 2 is also at high potential. As we know that, to trigger the 555 IC through Trigger PIN 2, the voltage of the PIN 2 must be below Vcc/3. So at this stage LED is OFF.
Now when we produce some sound near condenser mic, this sound will be converted into electrical energy and it will raise the potential at the Base, which will turn the Transistor ON. As soon as the transistor becomes ON, the potential at Point A would become low and it will trigger the 555 IC because of the low voltage (below Vcc/3) at Trigger Pin 2 and LED will turn ON. We have connected the LED to Output PIN 3 of 555 IC through a 220ohm resistor.

After some time LED will be turned OFF automatically because we are using 555 timer IC in Monostable Mode. LED will remain turned ON for 1.1*R1*C1 seconds. So we can see, with this formulae, that we can change this duration, by changing the value of Resistor R1 or/and Capacitor C1. We can modify this circuit using Relay to control the Electronic devices (120/220V AC). Control PIN 5 of 555 Timer IC should be connected to Ground through a 0.01uF capacitor.
To test this circuit you need to clap loudly as this small condenser mic don’t have long range. Or you can directly hit at the mic lightly (like I have done in the video).
In this circuit LED will be turned OFF automatically after some time, but what if we also want to control the switching OFF of the LED? Means if we want to turn ON the LED with a clap/sound and turn OFF it with second sound/clap? We can do this by using D-flipflop/IC 7474, I will show you this in my next circuit.


Ashish Patel says:

What’s that 220 k or E

Bipin Yadav says:

now in english, are you a idiot why you have put so many effect without reason ,have you seen your video before uploading

Bipin Yadav says:

abe chutiya hai kya bin matlab me itana effect daa ke rakha hai ,effect ke wajah se toh adha dikh hi nahi raha hai

Fix Electronics says:

Hello friend I have a offer for you.
You make electronic projects but do not earn . You can sell my electronic components in your videos. Contact Wats up no. 8669074868

Vipin Vijayan says:

In my case LED is always glowing. Help me how to resolve this issue ? Should i need to change any resistance value ? All resistance i used are same as per the diagram. Capacitor used 10uf 64 volts. Please give me a responce sir

Write a comment


Human Verification: In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Do you like our videos?
Do you want to see more like that?

Please click below to support us on Facebook!

Send this to a friend

▷ Other ReviewsVehicles   Show Cars   Motorbikes   Scooters   Rims & Tires   Luxury BoatsFashion   Sunglasses   Luxury Watches   Luxury Purses   Jeans Wear   High Heels   Perfumes   Jewellery   Cosmetics   Shaving Helpers   Fashion HatsFooding   Chef Club   Fooding Helpers   Coktails & LiquorsSports   Sport Shoes   Fitness & Detox   Golf Gear   Racquets   Diving Equipment   Ski Gear   Snowboards   Surf Boards   Rollers & SkatesEntertainment   DIY Guides   Zik Instruments   Published Books   Music Albums   Cine Movies   Trading Helpers   Make Money   Fishing Equipment   Paintball Supplies   Trading Card Games   Telescopes   Knives   VapesHigh Tech   Flat Screens   Tech Devices   Camera Lenses   Printers   USB Devices   PC Hardware   Network Gear   Cloud Servers   Software Helpers   Programmer Helpers   Mobile Apps   Hearing AidsHome   Home Furniture   Home Appliances   Beddings   Floor Layings   Barbecues   Aquarium Gear   Safe Boxes   Office Supplies   Security Locks   Cleaning ProductsKids   Baby Strollers   Child Car Seats   Remote ControlledTravel   Luggages & Bags   Airlines Seats   Hotel Rooms   Fun Trips   Cruise Ships   Mexico Tours